V8 Swap

Although there is plenty of space in the motor compartiment of the Chrysler Crossfire, Chrysler never released a Crossfire with a V8. The tuning company Startech did, however, make a V8, called the STARTECH Crossfire 6.1S. This Crossfire is equipped with a M113 engine, with a displacement of 6 liters, and only 1 was made supposedly.

If you want to swap your engine from the stock 3.2L M112 V6 (or the supercharged version of the SRT6) to a M113 V8, you need to make sure of a couple things. Big thanks to The Mercedes Swap Shop for providing information.

Component	Recommended P/N	Note
wire harness	A113 010 25 00	The wire harness should fit the ME2.8. There should be only black ECU connectors, 3 of which latch, and 1 6-pin wide plug.
alternator	-	More power requires more power, get any M113 alternator
exhaust headers	-	You need to combine the Crossfire exhaust with a M113 exhaust manifold. Just weld the "front" two to the crossfire back two.
transmission	A113 030 00 12 / A628 030 00 12 (even spaced) A112 030 06 12 / A112 030 08 12 (uneven spaced)	The bolt pattern of the transmission was changed around 2004, so "new" crossfires need a different ring plate. The bolt pattern is for the OLD one evenly spaced, whereas the NEW pattern has an offset between the two sides (and a side is where the extra hole is in).
stock ecu	-	You should modify your ME2.8.1 ECU from the Crossfire, by soldering on the missing drivers and running it with the right firmware. This is the hardest part, and expect at least 8 hours of labour to do it right (keeping alarm etc working). Contact The Mercedes Swap Shop for more information about this.
radiator hose	A202 501 59 82	Take one from the W202 C43
radiator fan assy	A202 505 42 55 (shroud) A113 200 01 23 (mechanical fan) A113 200 01 22 (mechanical fan clutch)	The stock radiator fan and plastic shroud is too deep. A full assembly with mechanical fan from a C43 (W202) should fit.
ac bracket	-	The AC needs a bracket, which is part of the driver side engine mount. Make sure you take this from a M113.
ac compressor to condenser hose	A202 830 50 15	The stock V6 engine is further back, so a shorter AC cable is required. Maybe this one fits.

Experience with installing a V8

1999 W220 S500 113.960 (ME2.1)

Issues

• The transmission output shaft yolk was bigger than the Crossfire driveshaft. The P/N of the flexdisk of the Crossfire is A 210 411 04 15, whereas the S500 was running the A 210 411 02 15. It was required to swap/replace the yolk from the old V6 transmission to the V8 transmission.
• The engine is missing the (front) MAP sensor, that is located between the idler pulley and the Air Pump Switchover Solenoid. The bracket and hole exist for it, however.
• The throttlebody on the engine was using an old-style connector, and a new throttlebody had to be used. Swapping the connector might be possible, but its not recommended.
• The coilpacks on the V8 were a different generation, with P/N A 000 158 73 03. This would not fit the newer harness, and had to be swapped out for the V6 coilpacks + 2 new ones. The connectors seem they fit, but won't because of the blade width inside the coilpacks.
• The alternator (P/N A 011 154 3202) did not use a plug for the 2 wires of the sense signal, and instead had 2 screw terminals (D+, B+) and a blade terminal (KL (15)). Cars fitted with a front SAM will use the KL line to identify if the alternator works. To fix this, you have to cut off the connector on the new wiring harness, and use only pin 1 of it, and run it to the D+ terminal. Another option is to buy a new alternator with the connector fitted.
• The power cable running from the battery to the alternator and starter motor was too short and didn't fit the V8 alternator.
• The A/C, powersteering, transmission oil cooler, all are longer than they should be and will have some issues fitting properly.