Difference between revisions of "ECU"
Jump to navigation
Jump to search
| Line 53: | Line 53: | ||
| − | ==== Pin-to-pcb ==== | + | ====Pin-to-pcb==== |
| − | SCI Transmit (Connector C4 pin 29) | + | SCI Transmit (Connector C4 pin 29) |
| − | SCI Receive (Connector C4 pin 32) runs to the 2 round resistors (?) located right-top of Connector C5 9-pin adapter on the back of the board | + | # resistor 21R5 next to crystal above the main C167 chip. |
| + | # bosch 30343 pin right side, 7th from top ('above' bosch logo) | ||
| + | |||
| + | SCI Receive (Connector C4 pin 32) | ||
| + | |||
| + | # runs to the 2 round resistors (?) located right-top of Connector C5 9-pin adapter on the back of the board | ||
| + | # goes to the other side, above connector c5, pin 1, second and third square...? | ||
Revision as of 14:37, 17 March 2024
The Chrysler Crossfire has been equipped with the Bosch ME 2.8 ECU, which is used by the Mercedes R170 series cars, such as the SLK 320.
Part numbers
| Part number | Model |
|---|---|
| A 112 153 53 79 | |
| A 112 153 86 79 | |
| A 112 153 32 79 | |
| A 112 153 57 79 | |
| A 112 153 76 79 |
Programming
It is programmable over the OBD2 port, software such as Eurocharged EuroFlash tool. Other options is to open up the ECU and flash the EPROM directly. The flashing over OBD2 is a feature that is also utilized by the Mercedes STAR Diagnostics software, for updating the ECU.
Featureset
The ECU is mainly the controller of the motor, such as managing the air-to-fuel ratios and ignition timing. Modifications on this software can include the following:
| Modification | Models | Description | Known tuners for the ECU |
|---|---|---|---|
| Pops and bangs | SRT-6, N/A | Changes timings on ignition to combust 'too late', causing the explosion to be partially in the exhaust. This is oftentimes programmed for when you decrease throttle. | Eurocharged |
| Increase neutral/park rev limit | SRT-6, N/A | Crossfires lock the RPM of the engine, while not in drive/gear, to 4000 RPM. This limit can be increased in the software. | ? |
| Supercharger/idler pulley modification | SRT-6 | A different Supercharger or idler pulley requires a different air-to-fuel ratio as the compressor will suck in more air. Additionally, it will also turn on faster because of the higher RPM. | Eurocharged |
| Different air intakes | SRT-6, N/A | The stock airbox of the Crossfire on both SRT-6 and N/A are smaller than their bigger cousins, the C320 and the SL55. Giving the car more air helps already, but a tune would make better use of this change. | Eurocharged |
TODO
- Add pinout
- Add product codes of the N/A and SRT versions
- Add links to ECU
- Add featureset of ME 2.8
Pin-to-pcb
SCI Transmit (Connector C4 pin 29)
- resistor 21R5 next to crystal above the main C167 chip.
- bosch 30343 pin right side, 7th from top ('above' bosch logo)
SCI Receive (Connector C4 pin 32)
- runs to the 2 round resistors (?) located right-top of Connector C5 9-pin adapter on the back of the board
- goes to the other side, above connector c5, pin 1, second and third square...?