Difference between revisions of "ECU"

From Crossfires.net wiki
Jump to navigation Jump to search
(Created page with "The Chrysler Crossfire has been equipped with the Bosch ME 2.8 ECU. It is programmable over the OBD2 port, software such as Eurocharged their EuroFlash tool. Other...")
 
 
(8 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
The Chrysler Crossfire has been equipped with the Bosch ME 2.8 ECU. It is programmable over the [[OBD2]] port, software such as [[Eurocharged]] their [[EuroFlash]] tool. Other options is to open up the ECU and flash the EPROM directly. The flashing over OBD2 is a feature that is also utilized by the [[Mercedes STAR Diagnostics]] software, for updating the ECU.
+
The Chrysler Crossfire has been equipped with the Bosch ME 2.8 ECU, which is used by the Mercedes [[R170]] series cars, [http://www.carecus.com/cars-engines-that-use-bosch-me-2-8-engine-control-unit such as the SLK 320].
  
−
===== TODO =====
+
===Part numbers===
−
- Add pinout
+
{| class="wikitable"
−
- Add product codes
+
|+
−
- Add links to ECU
+
!Part number
−
- Add featureset of ME 2.8
+
!Model
 +
|-
 +
|A 112 153 53 79
 +
|
 +
|-
 +
|A 112 153 86 79
 +
|
 +
|-
 +
|A 112 153 32 79
 +
|
 +
|-
 +
|A 112 153 57 79
 +
|
 +
|-
 +
|A 112 153 76 79
 +
|
 +
|}
 +
 
 +
===Programming===
 +
It is programmable over the [[OBD2]] port, software such as Eurocharged [[EuroFlash]] tool. Other options is to open up the ECU and flash the EPROM directly.
 +
The flashing over OBD2 is a feature that is also utilized by the [[Mercedes STAR Diagnostics]] software, for updating the ECU.
 +
 
 +
 
 +
===Featureset===
 +
 
 +
The ECU is mainly the controller of the motor, such as managing the air-to-fuel ratios and ignition timing.
 +
Modifications on this software can include the following:
 +
{| class="wikitable"
 +
|-
 +
!Modification!!Models!!Description!!Known tuners for the ECU
 +
|-
 +
|Pops and bangs||SRT-6, N/A||Changes timings on ignition to combust 'too late', causing the explosion to be partially in the exhaust. This is oftentimes programmed for when you decrease throttle.||Eurocharged
 +
|-
 +
|Increase neutral/park rev limit||SRT-6, N/A||Crossfires lock the RPM of the engine, while not in drive/gear, to 4000 RPM. This limit can be increased in the software.||?
 +
|-
 +
|Supercharger/idler pulley modification||SRT-6||A different Supercharger or idler pulley requires a different air-to-fuel ratio as the compressor will suck in more air. Additionally, it will also turn on faster because of the higher RPM.||Eurocharged
 +
|-
 +
|Different air intakes||SRT-6, N/A||The stock [[airbox]] of the Crossfire on both SRT-6 and N/A are smaller than their bigger cousins, the [[C320]] and the [[SL55]]. Giving the car more air helps already, but a tune would make better use of this change.||Eurocharged
 +
|}
 +
 
 +
=====TODO=====
 +
 
 +
*Add pinout
 +
*Add product codes of the N/A and SRT versions
 +
*Add links to ECU
 +
*Add featureset of ME 2.8
 +
 
 +
 
 +
====Pinout or something====
 +
SCI Transmit (Connector C4 pin 29)
 +
 
 +
#resistor 21R5 next to crystal above the main C167 chip.
 +
#bosch 30343 pin right side, 7th from top ('above' bosch logo)
 +
 
 +
SCI Receive (Connector C4 pin 32)
 +
 
 +
#runs to the 2 round resistors (?) located right-top of Connector C5 9-pin adapter on the back of the board
 +
#goes to the other side, above connector c5, pin 1, second and third square...?
 +
 
 +
 
 +
Second C167
 +
 
 +
* TXD @ left-corner, first test point pad from left-to-right
 +
* Boot pin @ 7-9-7-9 free pads on the right, left pads, 3rd from the bottom

Latest revision as of 14:41, 17 March 2024

The Chrysler Crossfire has been equipped with the Bosch ME 2.8 ECU, which is used by the Mercedes R170 series cars, such as the SLK 320.

Part numbers

Part number Model
A 112 153 53 79
A 112 153 86 79
A 112 153 32 79
A 112 153 57 79
A 112 153 76 79

Programming

It is programmable over the OBD2 port, software such as Eurocharged EuroFlash tool. Other options is to open up the ECU and flash the EPROM directly. The flashing over OBD2 is a feature that is also utilized by the Mercedes STAR Diagnostics software, for updating the ECU.


Featureset

The ECU is mainly the controller of the motor, such as managing the air-to-fuel ratios and ignition timing. Modifications on this software can include the following:

Modification Models Description Known tuners for the ECU
Pops and bangs SRT-6, N/A Changes timings on ignition to combust 'too late', causing the explosion to be partially in the exhaust. This is oftentimes programmed for when you decrease throttle. Eurocharged
Increase neutral/park rev limit SRT-6, N/A Crossfires lock the RPM of the engine, while not in drive/gear, to 4000 RPM. This limit can be increased in the software. ?
Supercharger/idler pulley modification SRT-6 A different Supercharger or idler pulley requires a different air-to-fuel ratio as the compressor will suck in more air. Additionally, it will also turn on faster because of the higher RPM. Eurocharged
Different air intakes SRT-6, N/A The stock airbox of the Crossfire on both SRT-6 and N/A are smaller than their bigger cousins, the C320 and the SL55. Giving the car more air helps already, but a tune would make better use of this change. Eurocharged
TODO
  • Add pinout
  • Add product codes of the N/A and SRT versions
  • Add links to ECU
  • Add featureset of ME 2.8


Pinout or something

SCI Transmit (Connector C4 pin 29)

  1. resistor 21R5 next to crystal above the main C167 chip.
  2. bosch 30343 pin right side, 7th from top ('above' bosch logo)

SCI Receive (Connector C4 pin 32)

  1. runs to the 2 round resistors (?) located right-top of Connector C5 9-pin adapter on the back of the board
  2. goes to the other side, above connector c5, pin 1, second and third square...?


Second C167

  • TXD @ left-corner, first test point pad from left-to-right
  • Boot pin @ 7-9-7-9 free pads on the right, left pads, 3rd from the bottom
Retrieved from "https://wiki.crossfires.net/index.php?title=ECU&oldid=285"